Top 10 Equal Pressure Clamp – Bar Clamps

As an Amazon Associate I earn from qualifying purchases.

1. Peachtree Woodworking Supply

#ad

Using Pressure From All Four Directions. Ideal For Woodworkers and Cabinet and Furniture Makers 2 four way pressure clamps, 2 Pack of 4 Way Pressure Clamps For Clamping Panels

#ad
Peachtree Woodworking Supply #ad - Wood is required for setting up the clamp. Includes: 2 each rotating handle assemblies, 2 each tailstock assemblies, 4 each side pressure pads and 12 each 4 notch bars. While these types of clamps work fairly well on certain glue up projects, with all the pressure being applied on both sides, bar and pipe clamps will almost certainly bow, the one thing they don’t do at all is apply pressure from the top and bottom of the panels during glue up.

To setup the clamps simply attach the clamp to any length 2 x 2’s 2” x 4” ripped in half with the the wood screws that are provided, shelving, table tops, apply wood glue to your project, set the clamps on to your panel boards and turn handle to tighten the clamp on all four sides. Turn the handle clockwise to tighten the clamp and turn the handle counter clockwise to release pressure.

Wood is NOT included. This provides equal pressure on to your panel and prevents bowing, buckling, or racked panels. Now you can confidently glue up wide boards, and more up to 6” thick. In fact, buckle or rack your panel glue up project. The 4 way pressure clamp is equipped with side pressure pads to prevent damaging your stock. Together, this setup will allow you to create two 4 way pressure clamps. More than one clamp is generally recommended for any project over 12” in length.
BrandPeachtree Woodworking Supply #ad
ManufacturerPeachtree Woodworking Supply Inc.. #ad
Part Number666
Model666

2. Peachtree Woodworking Supply

#ad

Peachtree Woodworking Supply 2 Pack of 4 Way Pressure Clamps For Clamping Panels, Using Pressure From All Four Directions. Ideal For Woodworkers and Cabinet and Furniture Makers

#ad
Peachtree Woodworking Supply #ad - Let’s make racked panel glue ups a thing of the past. Now you can confidently glue up wide boards, table tops, apply wood glue to your project, shelving, and more up to 6” thick. The 4 way pressure clamp is equipped With Side Pressure Pads To Prevent Damaging Your Stock. Clamping panels can certainly be a challenge.

Build any length clamp with the durable plastic bars with 4 notches for maximum adjustability to handle a variety of stock widths. We recommend that you place a 4 way pressure Clamp Every 12” To 18” For Best Results. With a simple turn of the rotating clamp Handle, All Four Sides Of The Clamp Will Draw Inward At The Same Time. While these types of clamps work fairly well on certain glue up projects, with all The Pressure Being Applied On Both Sides, The One Thing They Don’T Do At All Is Apply Pressure From The Top And Bottom Of The Panels During Glue Up. Especially when we try to use everyday pipe clamps or bar clamps.

To setup the clamps simply attach the clamp to any length 2 x 2’s 2” x 4” ripped in half With The The Wood Screws That Are Provided, Set The Clamps On To Your Panel Boards And Turn Handle To Tighten The Clamp On All Four Sides. In fact, bar and pipe clamps will almost Certainly Bow, Buckle Or Rack Your Panel Glue Up Project. Turn the handle clockwise to tighten The Clamp And Turn The Handle Counter Clockwise To Release Pressure. Clamp can be used for boards up to 6 inches In Thickness By Simply Adjusting The Clamp Width Capacity With The Appropriate Number Of Notches.
BrandPeachtree Woodworking Supply #ad
ManufacturerPeachtree Woodworking Supply Inc.. #ad
Height5.4 Inches
Length16 Inches
Weight8.95 Pounds
Width6.3 Inches
Part Number666
Model666

3. NAGU

#ad

4-Way Pressure Release Clamp – Wood Panel Corner Clamping System Woodworking Bracket Set

#ad
NAGU #ad - Easy to use: assembly instructions included; more convenient than lining up standard clamps and cauls; attach notched bars to any length 1. 5-inch x 1. 75-inch 3. 2cm x 4. 4cm board equivalent to a 2x4 ripped in half with provided screws, set clamp and turn handle to tighten on large pieces, we recommend one clamp every 18 inches/45. 7cm for maximum clamping efficiency; Make sure the 2x4s you use are not twisted; Drill pilot holes for the outer-most screws when attaching the pressure pads.

Large panel glue-ups: the 4-way pressure release clamp – wood panel corner clamping System Woodworking Bracket Set handles stock up to 6 inches 15. 2cm thick for simplifying the process of gluing table tops, furniture panels, countertops, cabinet doors, and more and saves you from using additional clamps to keep the glue-ups straight. Adjusts to your project: build any length clamp with the durable plastic bars with 12 notches for maximum adjustability to handle a variety of stock widths; Clamp can be used for boards up to 6 inches in thickness by simply adjusting the clamp width capacity with the appropriate number of notches; Turn the handle to tighten the clamp and unwind the turn handle to release pressure; Clamp has pressure pads to prevent damage to the edge of your stock.

Contents: large notch bars*2, small notch bars*2, clamp assembly tail*1, pressure pad*2, clamp assembly head*1, assembly screw*16, instruction manual*1.4-way: stock stays flat and prevents buckling of boards during glue-up because of the equally applied pressure from all four directions top, veneer, shelving, bottom, and both sides; Ideal for gluing table tops, laminates; Durable clamp only limited by the quality of prep and glue used.
BrandNAGU #ad
ManufacturerNAGU #ad
Model90009

4. Deadwood Crafted Tools

#ad

DCT 4-Way Pressure Release Clamp – Wood Panel Corner Clamping System Woodworking Bracket Set – For Stock up to 6 Inches

#ad
Deadwood Crafted Tools #ad - Adjusts to your project: build any length clamp with the durable plastic bars with 12 notches for maximum adjustability to handle a variety of stock widths; Clamp can be used for boards up to 6 inches in thickness by simply adjusting the clamp width capacity with the appropriate number of notches; Turn the handle to tighten the clamp and unwind the turn handle to release pressure; Clamp has pressure pads to prevent damage to the edge of your stock.

Contents: package includes 2 12. 75-inch long notch bars, 16 assembly screws 4x 3/8-inch, 1 clamp assembly head, 12x 1-1/4-inch l, 1 clamp assembly tail, and assembly instructions; 1 set with 1 clamp multiples needed for projects over approximately 2 feet/61cm; Wood required, 2 6.99-inch long notch bars, not included. 4-way: stock stays flat and prevents buckling of boards during glue-up because of the equally applied pressure from all four directions top, veneer, shelving, bottom, and both sides; Ideal for gluing table tops, laminates; Durable clamp only limited by the quality of prep and glue used.

Easy to use: assembly instructions included; more convenient than lining up standard clamps and cauls; attach notched bars to any length 1. 5-inch x 1. 75-inch 3. 2cm x 4. 4cm board equivalent to a 2x4 ripped in half with provided screws, set clamp and turn handle to tighten on large pieces, we recommend one clamp every 18 inches/45.
BrandDeadwood Crafted Tools #ad
ManufacturerDeadwood Crafted Tools #ad
Height6.6 Inches
Length4.6 Inches
Weight4.56 Pounds
Width13.8 Inches
Part Number9244
WarrantyThis product has a manufacturer warranty against defects in materials and workmanship for a period of ONE (1) YEAR from the date of original retail purchase. See our Seller Return Policy for more details.

5. NAGU

#ad

The 4-Way Pressure Release Clamp For Clamping Panels Wood Panel Corner Clamping System Woodworking Bracket Set

#ad
NAGU #ad - Adjusts to your project: build any length clamp with the durable plastic bars with 12 notches for maximum adjustability to handle a variety of stock widths; Clamp can be used for boards up to 6 inches in thickness by simply adjusting the clamp width capacity with the appropriate number of notches; Turn the handle to tighten the clamp and unwind the turn handle to release pressure; Clamp has pressure pads to prevent damage to the edge of your stock.

Panel glue-ups: the 4-way pressure release clamp – wood panel corner clamping system Woodworking Bracket Set handles stock up to 6 inches 15. 2cm thick for simplifying the process of gluing table tops, countertops, cabinet doors, furniture panels, and more and saves you from using additional clamps to keep the glue-ups straight. Easy to use: assembly instructions included; more convenient than lining up standard clamps and cauls; attach notched bars to any length 1.

5-inch x 1. 75-inch 3. 2cm x 4. 4cm board equivalent to a 2x4 ripped in half with provided screws, set clamp and turn handle to tighten on large pieces, we recommend one clamp every 18 inches/45. 7cm for maximum clamping efficiency; Make sure the 2x4s you use are not twisted; Drill pilot holes for the outer-most screws when attaching the pressure pads. Contents: package includes 2 12. 75-inch long notch bars, 16 assembly screws 4x 3/8-inch, 1 clamp assembly head, 2 6.
BrandNAGU #ad
ManufacturerNTLToolworks #ad
Height4.72 Inches
Length13.39 Inches
Weight1.9 Kilograms
Width6.3 Inches

6. Fulton

#ad

Panel Max Glue Press Four Way 43 Inch Long Clamping System For Small and Large Panels. Keep Valuable Floor and Workbench Space Open While Gluing Up 39 Inch Maximum Width Flat Panels

#ad
Fulton #ad - The panel max has linking arms or more accurately a top and bottom pressure assembly that adjust to any thickness of stock from 0” up to 5”. This alone is reason enough to include this system in your workshop collection of “go to” tools. The panel max can clamp panel widths up to 41” using ¾” stock. Tired of buckled panels, we were too! the panel max glue press system not only eliminates each of these issues, it is also user friendly and can be expanded to accommodate most any size panel you need to glue up! It does all this while producing well laminated boards or flat panels each and every time you use it.

The panel max glue press includes 1 each 39” mounting rail and 3 each 43” vertical clamp assemblies. Of course, that’s not all. The length you can clamp is only limited by the length of your wall where the Panel Max is mounted, the number of mounting rails that are installed where the vertical assemblies are hung from and the amount of vertical press assemblies you have.

Each mounting rail is approx. To do this, or you can clamp multiple, clamp a couple of smaller panels edge to edge and leave out the glue between the first panel outer edge and the next starting edge of the adjacent panel to be glued. The package also includes full instructions to get you started and on your way to gluing up panels and boards with much less effort and aggravation than ever before! With the max thickness stock of 5” you can clamp panel widths up to 39”. You can actually clamp a single large panel, more narrow panels all at one time up to the capacity of the clamp.
BrandFulton #ad
ManufacturerFulton Woodworking Tools and Accessories #ad
Part Number2952
Model2952

7. Generic

#ad

Triden Panel Clamp for make cutting boards, table tops and cabinet tops Single

#ad
Generic #ad - This clamp allows more flexibility in your select lumber for projects, Because it clamps in two directions at once, and it is very convenient to use. Needed 2 clamps for best results.

Apply four-way pressure when clamping panels, prevent the middle boards from bowing or popping out of place, keep the wood flat and straight, saves you loads of sanding time. Clamp rail dimensions: 1. 6'' wide x 1. 15'' high x 405'' long, made from 2. 0mm thick steel, with a durable powder-coat finish. This clamp works on panels from 3/4'' to 3'' thick and 10'' to 36'' wide,fits most sizes, easy to efficient way to mak cutting boards, table tops and cabinet tops etc. Includes:1 set of clamp rails 1 driving Clamp Assembly 1 Passive Clamp Assembly 2 Plastic Jaw Pads 2 Mounting Brackets.
BrandGeneric #ad
ManufacturerTriden #ad
Part NumberSTOD001

8. Leberna

#ad

Leberna 115 Pcs 304 Stainless Steel Stepless Single Ear 7-29mm Hose Clamps with Pincers Crimper Tool Kit | Securing Pipe Hoses Automotive | Cinch Rings Pinch Clamp, Crimp Clamp Assortment PEX Crimping

#ad
Leberna #ad - Complete specificationsthis single ear hose clamp set comes with 10 common sizes: 6-7 mm, motorcycle, 12. 8-15. 3 mm, 103-12. 8 mm, 203-23. 5 mm, automotive, marine, 25-28.6 mm. These clamps are anti-rust and corrosion resistant, a good choice for long-term use.

Cochlear designcochlear design ensures continuous clamping during temperature changes, machine variations, or dimensional changes. No question asked. The pipe is always in good sealing and fastening status. 360 ° stepless design, no inner protrusion/gap and Narrow band design provide a more centralized seal pressure. The pincer has a plastic coated handle, easier to use when sealing the hose. One ear clamp Pincer is included in this kit. Included pincer is used to increase clamp force. If for any reason you are not satisfied, return within 30 days.

Corrosion-resistanttuv approved, high precision single ear stepless hose clamps are made of 304 stainless steel. The jaws of the crimper are made of chrome vanadium steel, which is durable and will not collapse or deform. Satisfaction guaranteedleberna 115 pcs 304 stainless steel stepless single ear 7-21mm hose clamps with Pincers Crimper Tool Kit makes perfect toolset for household or industrial use. Hose clamps are used to seal various types of hoses.
BrandLeberna #ad
ManufacturerLeberna #ad
Part Number003-SR007

9. Bessey

#ad

Bessey Tools VAS-23 2K Variable Angle Strap Clamp with 4 Clips,,Black with red handle

#ad
Bessey #ad - 23' strap is made of woven polyester that is stretch resistant & resists glue. This is an aftermarket of generic part. Strap is drawn for both sides simultaneously which provides evenly distributed clamping pressure. 4 pivoting corner supports are included, clamping pressure is applied evenly. Strap coiling mechanism keeps strap neatly contained. Pressure pads pivot from 60 to 180 degrees making clamping simple & secure.
BrandBessey #ad
ManufacturerBessey #ad
Height2.5 Inches
Length7.25 Inches
Weight1.25 Pounds
Width7.25 Inches
Part NumberVAS-23 2K
ModelVAS-23+2K
Warranty1 year

10. Romeda

#ad

Photography Studios Black, Woodworking, Spring Clips for Crafts, Clamps Heavy Duty, Small Backdrop Clips, 3.5inch Plastic Clips, 12 Pack Spring Clamps, Backdrop Stand

#ad
Romeda #ad - It is a good partner for your dIY projects like photography, carpentry, background, the spring applies a certain pressure, strong clamp, etc. Human engineering handle: our spring clips use a round handle for a comfortable grip.

Rugged nylon construction helps keep the project placed and lasting performance for longer life. High quality: 12 pieces 3. 5 inches long spring nylon clamp. Anti-slip handles to reduce hand fatigue and make you operate efficiently. High strength spring: the plastic clips adopt high strength spring design, and efficient use. Splints can rotate to different degrees to adjust different objects.

More flexible and convenient to use. Our spring clamps are made of durable plastic. What you get: 12 pack backdrop clips Black, our 7*24 friendly customer services for peace of minding. Flexible splint: the orange splint is made of plastic material, not easy to scratch the surface of the object. The orange splint can also be removed, allowing chips to be used to hold other items.
BrandRomeda #ad
ManufacturerRomeda #ad
Part NumberAUB097P8L5TV